How to install the fuser film sleeve correctly

<p>Step 1: Disassemble the components</p><p>1) Remove the fixing assembly, disassemble the sub-housing, take off the fixing assembly, pay attention to the gears and plug wires when taking it.</p><p>1.1) Disassemble the fixing assembly, and remove the bayonet of each plastic part carefully to avoid damage. And remember to disassemble first and install later, and install later.</p><p><br></p><p>Step 2: Take the <a href="https://www.ascendimage.com/fuser-film-sleeve" rel="noopener noreferrer" target="_blank">fuser film sleeve</a></p><p>2) Remove the damaged fuser film sleeve, clean the ceramic heater and the surface of the bracket with a cotton swab moistened with alcohol; (must be cleaned to avoid damage to the fuser film sleeve&nbsp;again).</p><p><br></p><p>Step 3: Wipe lubricant</p><p>3) Use a plastic rod, a small wooden piece or your fingers to dig out some grease from the container; on the part of the ceramic heater and the holder that contact the fuser film sleeve, apply more on the edges of each, and the other 15-20 places evenly Put on grease;</p><p>A4 format printer: 0.5-1.0 grams of grease</p><p>A3 format printer: 0.75-1.5 grams of grease</p><p>(Note: Remember that the surface of the fuser film sleeve&nbsp;should not be stained with silicone grease, so as to avoid slippage of the fuser film sleeve&nbsp;and paper jam in the fixing part)</p><p><br></p><p>Step 4: Apply back and forth</p><p>4) Use plastic or wooden pieces or fingers to apply back and forth on the ceramic heating plate and the support surface until the grease is evenly distributed on the ceramic heating plate and the support surface.</p><p><br></p><p>Step 5: Install the fuser film sleeve</p><p>5) Install the fuser film sleeve, and make sure that the side with the grounding ring (black side) is on the same side as the conductive ring (black rubber conductive gear) or conductive brush of the lower roller. Remember not to install it backwards! ! !</p><p><br></p><p>Step 6: Assemble the components</p><p>6) Turn the fuser film sleeve&nbsp;several times by hand. When you feel the fuser film sleeve&nbsp;moves smoothly, you can assemble the fuser film sleeve&nbsp;and the lower roller.</p><p>Note: After installing the fuser film sleeve. Follow the steps to disassemble and install.</p><p>Step 7: Repeat self-check</p><p>7) When all the installations are completed, turn on the machine and run the self-check for 3 to 5 times (ie: open the front cover and close the self-check repeatedly) Purpose: Let the fuser film sleeve&nbsp;run idly, and test a few more sheets after completion without jamming That is OK.</p><p><br></p><p>Notes on fuser film sleeve&nbsp;installation</p><p>1. Make sure to replace the original fuser film sleeve;</p><p>2. Disassemble the fixing assembly, and carefully remove the bayonet of each plastic part to avoid damage. It must be remembered to disassemble first and install later, and disassemble later to install first;</p><p>3. When installing and removing the fuser film sleeve, pay attention to protect the heating ceramic sheet in the fuser film sleeve;</p><p>4. When installing the fuser film sleeve, pay attention to the direction of the film, and at the same time, ensure that the surface of the film is flat, otherwise it will easily cause paper jams and damage the fuser film sleeve&nbsp;again;</p><p>5. Check the lower fuser roller and the shaft sleeve to see if there is any wear, and replace if there is any;</p><p>Note: When replacing the lower fuser roller sleeve, it is best to add a little grease to reduce the wear caused by friction.</p><p><br></p>