products
Would you like to react to this message? Create an account in a few clicks or log in to continue.
products

products and price


You are not connected. Please login or register

Ten problems with PCB board

Go down  Message [Page 1 of 1]

1Ten problems with PCB board Empty Ten problems with PCB board Mon Nov 30, 2020 5:00 am

Admin


Admin

<p><strong>1. Character placement is unreasonable</strong></p><p>&nbsp;</p><p><br></p><p>The character cover pad SMD soldering piece brings great inconvenience to the soldering of the component and the on-off test of the printed board.</p><p><br></p><p>&nbsp;</p><p><br></p><p>The character design is too small, which makes screen printing difficult, and the over-construction causes characters to be stacked on each other, making it difficult to distinguish.</p><p><br></p><p>&nbsp;</p><p><br></p><p><strong>2. the processing industry can not clarify</strong></p><p>&nbsp;</p><p><br></p><p>The single-panel design is on the TOP layer. If it is not clarified, it will be done in reverse. The fabricated board is also lacking in good soldering.</p><p><br></p><p>&nbsp;</p><p><br></p><p>For example, a four-layer <a href="https://www.rocket-pcb.com/products" rel="noopener noreferrer" target="_blank"><strong>PCB board design</strong></a> uses four layers of TOP mid1 and mid2 bottom, but the processing is not placed at the same time, which requires clarification.</p><p><br></p><p>&nbsp;</p><p><br></p><p><strong>3. Draw pads with padding</strong></p><p>&nbsp;</p><p><br></p><p>When designing the circuit, the pad can be traced by the DRC, but the processing is not possible, because such a pad can not directly generate solder resist data. When the solder resist is applied, the pad area will be a solder resist. Covering, making the device difficult to solder.</p><p><br></p><p>&nbsp;</p><p><br></p><p><strong>4. Single-sided pad aperture setting</strong></p><p><br></p><p>&nbsp;</p><p><br></p><p>Single-sided pads are generally not required to be drilled. If drilling is required, they should be marked and their aperture should be designed to zero. If a numerical value is designed, perhaps when the drilling data occurs, this position presents the coordinates of the hole and the problem is presented.</p><p><br></p><p>&nbsp;</p><p><br></p><p>Single-sided pads should be marked if they need to be drilled.</p><p><br></p><p><br></p><p><strong>5. Stacking of pads</strong></p><p>&nbsp;</p><p><br></p><p>The stacking of the pads (except for the surface pads) means that the holes are stacked. During the drilling process, the drill bit is broken due to repeated drilling at one place, causing damage to the holes.</p><p><br></p><p>&nbsp;</p><p><br></p><p>In the <a href="https://www.rocket-pcb.com/multilayer-pcb" rel="noopener noreferrer" target="_blank"><strong>multi-layer PCB board</strong></a>, two holes are stacked, one hole should be the isolation plate, and the other hole is the connection plate, otherwise, the film will be represented as the isolation disk after the negative film is formed, which will be scrapped.</p><p><br></p><p>&nbsp;</p><p><br></p><p><strong>6. The abuse of the graphics layer</strong></p><p>&nbsp;</p><p><br></p><p>Unusual wiring is done on some graphics layers, that is, four-layer boards are designed with more than five layers, which will form a misinterpretation.</p><p><br></p><p>&nbsp;</p><p><br></p><p>In the design time chart, used as an example to draw the lines of each layer with the Board layer, and use the Board layer to mark the line. When the data is being drawn, the missing layer is not selected. The open-circuit may be short-circuited by selecting the label line of the Board layer, so the design layer adheres to the integrity and clarity of the graphic layer.</p><p><br></p><p>&nbsp;</p><p><br></p><p>In contrast to conventional designs, such as the component surface design in the Bottom layer, the welding surface design in the Top, creating unnecessary trouble.</p><p><br></p><p>&nbsp;</p><p><br></p><p><strong>7. The electric ground layer is the connection and the flower pad.</strong></p><p>&nbsp;</p><p><br></p><p>Because of the power supply designed as a flower pad method, the ground layer is the opposite of the image on the practical printed board, and all connections are isolated lines, which should be very clear to the designer. When drawing several sets of power supply or isolation lines of several grounds, be careful not to close them to avoid a short circuit between the two groups.</p><p><br></p><p>&nbsp;</p><p><br></p><p>8. There are too many filler blocks in the design or the filling block is filled with very thin lines.</p><p>&nbsp;</p><p><br></p><p>There is a loss of sight in the raw light painting data, and the light painting data is not complete.</p><p><br></p><p>&nbsp;</p><p><br></p><p>The filling block is drawn one by one in the line of light painting data processing, so the amount of light drawing data generated is quite large, adding the difficulty of data processing.</p><p><br></p><p>&nbsp;</p><p><br></p><p><strong>9. The spacing of the area grid is too small</strong></p><p>&nbsp;</p><p><br></p><p>The edge between the large-area grid lines and the same line is too small (less than 0.3mm). In the manufacturing process of the printed board, the image transfer process easily occurs after the shadow is formed, and a lot of broken film adheres to the board to form a broken line.</p><p><br></p><p>&nbsp;</p><p><br></p><p><strong>10.Don't understand the design of the frame</strong></p><p><br></p><p>&nbsp;</p><p><br></p><p>The customer has designed the outline lines in the Keep out layer, the Board layer, the Top over layer, etc., and these outline lines do not coincide, which makes it difficult to determine which shape line the PCB reverse engineer is based on.</p>

https://weyes123.666forum.com

Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum