Home
<p>How to operate the vertical injection molding machine? The operation process of the <a href="https://www.hisson.com/pet-blow-moulding-machine" rel="noopener noreferrer" target="_blank"><strong>vertical injection molding machine</strong></a> has always been a problem that everyone needs to look for. In fact, the operation of the vertical injection molding machine is very simple. What is the use process of the vertical injection molding machine?</p><p><br></p><p>Operation process of vertical injection molding machine:</p><p><br></p><p>1. Before starting the machine, check whether the lubrication parts are completely lubricated.</p><p><br></p><p>2. Check whether the oil pump has abnormal noise, carefully install and tighten the mold, pay attention to safety when fixing the upper and lower molds, adjust the pressure of each part, set the manual operation and temperature adjustment of each part, and manually adjust the position of each switch to ensure the mold Safety.</p><p><br></p><p>3. Set the ldquo and manual button of the electronic control panel to ON. When the machine is manually operated, the action button only works when the button (ON) is pressed on the electronic control panel, and each action disappears when the button is pressed.</p><p><br></p><p>4. Mode adjustment: First, adjust the high-voltage proximity switch stroke block to the lowest point, then install the mold in the center between the upper and lower molds, and then press the "ldquo" button on the electronic control panel to adjust the mold (extract). At this time, the template begins to close the mold at low pressure and low speed.</p><p><br></p><p>5. When the mold is closed tightly, the mold closes the high voltage near the pull switch block to the high pressure position. At this time, according to the manual "ldquo", when the mold button is closed, the high pressure meter starts from high pressure.</p><p><br></p><p>6. Off mode: In semi-automatic mode, press the console with both hands to automatically start the button. At this time, the <a href="https://www.hisson.com/product" rel="noopener noreferrer" target="_blank"><strong>injection moulding machine</strong></a> shuts down and the mold closes quickly.</p><p><br></p><p>When the mold is closed, the mold is closed. The speed slows down and the mold closes. A high-voltage clamp is generated when the high-voltage proximity switch block is contacted with the mold.</p><p><br></p><p>7. Valve seat: used when adjusting the mold to the mold, that is, to control the advancement of the nozzle cylinder table.</p><p><br></p><p>8. Seat backrest: used when adjusting the mold to the mold, that is, control the nozzle cylinder to move backwards</p><p><br></p><p>9. Injection: According to the material, shape, size, adjust the injection pressure, keep the pressure beyond the time and position, press the "injection button" to make glue. (Note: The temperature can reach the set value before making glue).</p><p><br></p><p>10. Screw feeding: According to "ldquo", after the feeding button, the screw rotates the rubber to stir and mix, and the compression screw rises (the rising speed is determined by the adjustment of the back pressure regulating valve). When the rising action of the screw reaches the feeding approach, the stop is switched on and off to feed The feed motion stops, and the size of the feed stroke depends on the amount of glue required by the product.</p><p><br></p><p>11. Release:</p><p><br></p><p>(1) When the user manual is pressed, after the button is loosened, the screw moves upward to perform a back movement.</p><p><br></p><p>(2) When using the semi-start, the loosening action is mainly to pull the screw out a certain distance after the automatic feeding is completed (the distance is determined by the loosening time).</p><p><br></p><p>The purpose of this operation is to prevent the rubber from being compressed due to the feed. The expansion caused by thermal contraction overflows at the barrel mouth (ie, the funnel), blocking the flow path of the mold, and the rubber cannot be injected into the mold feed port again.</p><p><br></p><p>12. Eject: Press the "top" button to eject the product, you can adjust the semi-automatic time before and after the eject time to determine the eject height.</p><p><br></p><p>13. Back at the top: Press the "top" button, the thimble will automatically return to the original position, and the automatic adjustment time can be adjusted to determine the ejector retracting time.</p><p><br></p><p>14. Number of thimble: Set the number of semi-automatic thimble to determine the number of ejections.</p><p><br></p><p>15. Shutdown: Turn off the switch on the control panel, turn off the main power supply, and clean up the debris on the machine.</p><p><br></p><p> Vertical injection molding machine</p><p><br></p><p>The operation process of the vertical injection molding machine is shared with everyone. It looks complicated, but it is actually very simple to operate. As long as you get started, you can learn the specific operation process. I hope that the above sharing will be helpful to everyone.</p>
products
