Home
<p>Wooden <a href="https://www.uliandisplay.com/product" rel="noopener noreferrer" target="_blank"><strong><u>display stands</u></strong></a> are ideal for displaying home artwork, community event posters, personal bulletin boards, and chalk boards. </p><p>They are portable and perfect for folding in your car for easy transportation to family parties, parties or business talks. </p><p>They can be placed on the table top or on the floor. </p><p>It is easy to make easel with some simple materials and a few hours in the store at home. Cut the 5/8-</p><p>Inch flat Model 4 pieces. </p><p>Cut three of them 22 inch long, and cut one 10 inch long. </p><p>Polish any rough edges with 120grit sandpaper. </p><p>Set the angle of the saw cut to 67 1/2-degrees. </p><p>1/2-2</p><p>Degree cut of two top in 5/8</p><p>Flat model. </p><p>Polish any rough edges with 120grit sandpaper. </p><p>Place three pieces 22-</p><p>The inch plane forming faces towards a working surface and clamping them together flush along the top edge so that the sides of the two 67 are 1/2-</p><p>The inch angle cuts face each other and is firmly pressed against the uncut central part. </p><p>Three pieces are clipped together to form about 30-Triangle of degree. Drill a 1/8-</p><p>1/2 inch down from the top through the inches holes of three pieces of wood that are clamped. Push the 1/8-inch by 2-</p><p>The inch black stove bolt through the holes in three pieces of wood. </p><p>Attach the wing nut to the bolt and tighten it. </p><p>Remove the clip. </p><p>You now have a tripod for the <a href="https://www.uliandisplay.com/product" rel="noopener noreferrer" target="_blank"><strong><u>display stand. </u></strong></a></p><p>Measure 3 inch up from the bottom of two side blocks of 5/8</p><p>Inch flat mold, draw a small pencil line on the back of each side plate. </p><p>Place the tripod face down. </p><p>Locate the block of 10-inch 5/8-</p><p>Inch Flat dies go horizontally through the back of the two side plates and flush on the side, placing the bottom of the Plate along the pencil line. Pre-drill 1/16-</p><p>10-inch holes on both sides</p><p>Inch plate, through 10-</p><p>Inch plate and 1/4-</p><p>Inch to the back of the side plate. </p><p>Screw two 1-</p><p>10-inch black wooden screws-</p><p>Inch plate of two side plates. </p><p>This is the rear cross. </p><p>A bracket of the easel. </p><p>Turn over the easel and put it up. </p><p>Measure 2 inch up from the bottom of the two side plates and make a light pencil mark in the middle. Drill one 3/8-</p><p>The inches hole in the center of each side plate is about 1/4-</p><p>You made a pencil mark on the wood. </p><p>1 1/4 glue</p><p>Inch pins for these holes. </p><p>The pin is the bracket that displays the item. </p><p>Two screws 1/2-</p><p>Inch brass screw hook. </p><p>Screw one of the hooks into 10-</p><p>Inch cross-pieces and 4 other 1/2-</p><p>Up inches from the bottom of center 22-</p><p>Inch flat template. </p><p>Connect the brass chain to two hooks. </p><p>With 3/4-nail three black rubber foot pads to the bottom of each template</p><p>One inch flat head DingTalk.</p>
products
